abrasive material
英 [əˈbreɪsɪv məˈtɪəriəl]
美 [əˈbreɪsɪv məˈtɪriəl]
磨料
英英释义
noun
双语例句
- With the orthogonal tests the influence of work condition of the 3-phase abrasive water jet to material removal and erosion depth is analyzed, and the relationship between the abrasive granularity and the surface roughness is discussed.
通过正交试验，分析了三相射流工作条件对材料去除量和冲蚀深度的影响，讨论了磨料粒度与加工表面粗糙度的关系。 - On the basis of the characteristics of the lubrication film, surface texture, abrasive particle material and work conditions, it sets up the wear rate analysis calculation formula of piston ring and cylinder liner.
本文在考虑了油膜特性、形貌特性、磨粒特性、材料特性及工况条件等因素的基础上，导出了活塞环&缸套的三体磨粒磨损分析计算公式。 - The company engages in the production and sales of glass tools, abrasive, abrasive tools, technics material and hardware accessories.
本公司专业从事玻璃工具、磨料磨具、工艺材料、五金配件的生产销售业务。 - Particular attention is paid to the analysis of the effects of some major process parameters, such as air pressure, abrasive material, size and supply rate, nozzle shape and dimension, stand-off distance and workpiece material on the cutting performance and kerf characteristics.
重点分析了一些主要的加工参数，例如空气压力、磨料材料、尺寸、供给率、喷嘴的形状和尺寸、喷射距离以及工件材料，对切削性能和切口特征的影响。 - After abrasive material granularity reaches given size, the processing effect will not change;
当磨料粒度降低到一定的大小后，磨抛垫对硅片的抛光效果将不会有太大的变化； - The test results show that wear resistance of tested steel under low stress abrasive depends on material hardness. Wear resistance of quenched microstructure is highest.
结果表明：低应力磨粒磨损的耐磨性主要取决于材料的硬度，淬火态组织的耐磨性最好。 - It is performed through the verification and analysis of the interrelation of typical materials cutting features ( cutting depth, kerf width, striking capacity) and cutting variables ( water pressure, target distance, cutting rate and so on) and the effeCts of abrasive and material.
验证分析了典型材料的切割特征（切割深度、切口宽度、冲蚀量）与切割变量（水压、靶距、切速等）的关系，以及磨料、材质两大因素的影响。 - In terms of pre concentration strengthening, more crushing and less grinding, abrasive resistant material usage and classification intensification, the paper describes the present situation of grinding classification both in and outside China and discusses on the development orientation of grinding classification in China's metallurgical mines.
本文从强化预选、多碎少磨、应用耐磨材料和强化分级三个方面论述了国内外磨矿分级的现状，探讨了我国冶金矿山磨矿分级的发展方向。 - Design of PLC Control System of a Deburring Equipment with Abrasive Material
一种磨料刷去毛刺设备的PLC控制系统设计 - A set of construction procedure has been made based on RS-9 insulating liner material and RS-17E abrasive liner material which are used in catalytic cracking equipments of petrochemical plants. It points out notices for each process and ensures construction quality.
针对美国RESCO公司隔热衬里材料RS9和耐磨衬里材料RS17E用于石油化工厂催化裂化装置制定了一整套施工程序，提出了各工序的注意事项，从而确保了施工质量。